Tag Archives: Kitbash

25 Hopper Interiors Completed

Posted on by
Reply

Slowly but surely over the last few weeks I’ve been working on completing the interior detailing on all of the Walthers hoppers I’ve stripped so far. That’s a total of 25 cars currently in progress at the same time. (This actually represents a little under half my current fleet of these cars.)

These twenty-five cars now have the interior bracing and the treatment to the top chord completed. I explain the modifications a bit more in this previous post, but the process basically involves patching the holes on the inside of the body (where the solid bulkhead part from the stock model was fitted) with body putty, adding the extended lip over the end of the car, filing the top of the sides smooth, instead of the peaked side on the model representing an angle iron for stiffening, and finally installing the new interior bracing. On the older cars I did, I fashioned the bracing from .040″ brass wire, but I’ve now taken to using 3/64″ (.047″) styrene rod from Evergreen to make these, as it’s far easier to file and work with, and the welded styrene-styrene bond is stronger and more flexible than the brittle CA bond to glue the brass to the plastic body.

IMG_8562 IMG_8563

Now i just need to get the other twenty end platforms all up to the same point…

Backdated ExactRail 65′ CP Gondola – Part 2: Corner ladders

Posted on by
2

In my previous post, I cut away and replaced the ends on an ExactRail 65′ Hawker-Siddeley CP gondola to backdate the model to an older National Steel Car version of a similar car. After a couple more evenings of work, the car now has its new corner ladders installed.

The last bit of major surgery on the car body was to carve away the top chord over the last panel on the right hand side of the car, as the NSC cars have a notch here for taller ladders. Comparing prototype photos of the NSC and H-S (which the stock model represents) versions, the NSC car has a 5-rung ladder with closer spacing compared to a 4-rung ladder on the H-S car. With the top chord cut away, the area was filed smooth and the new notched bit formed out of a scale 2″x6″ top piece and an angled bit cut and filed from a piece of 6″x6″. This little assembly was then cemented in place, and the cracks and seams filled in with Bondo body putty. (At this time the seams between the new end and the sides of the car body were also touched up with body putty.)

IMG_8495

After the putty set up overnight, everything was filed and wet-sanded smooth. Then the ladders could be installed.

The ladders are cut to length from Tichy 8-rung boxcar ladders, and the rung spacing works out perfectly. Note the sides have a 5-rung ladder, and the ends have a shorter 4-rung ladder. The rungs of the side and end ladders align which each other. Note also that on the H-S car, the ladders are mounted below the heavy top chord, but on the NSC car that the modified model is intended to represent the top rung of the ladder is in front of the shallow top chord on the end, and located within a notch in the heavy side top chord.

IMG_8494

Also unlike the later H-S car, which has ladders at every corner of the car, the opposite corners on the NSC car just have a pair of grab irons instead of full ladders. The next step will involve drilling and installed these, and a few other minor details, and then I’ll be able to tackle the underframe modifications.

Backdated ExactRail 65′ CP Gondola – Part 1

Posted on by
2

A good portion of the traffic on the Algoma Central is finished steel products, and as a 300 mile wilderness route with no industrial users of this steel, basically one hundred percent of this traffic was interchanged to other railways, particularly in Sault Ste. Marie (CP and SOO Line), Oba (CN) and to a lesser extent Franz (CP). As such, CN and CP also provided a certain amount of cars for steel loading, so open cars from these railways would also be a regular sight on Algoma Central trains.

A few years ago, ExactRail released a model in their “Signature Series” of a Canadian Pacific 65′ gondola. This car is based on a version of a car built in the early to mid 1970s by Hawker-Siddeley and Marine Industries. Many of these are still in service today, so this is an excellent choice to be a part of my Canadian Pacific fleet. To add a little variety to the several cars I’ve collected, I’ve always been intending to take at least one car and backdate it to a late 1960s National Steel Car version of the same car. The NSC version is almost identical, having the same overall dimensions, number of side ribs, tie downs, etc., but has different ends and ladder arrangements. While the later HST/MIL cars have a distinctive ribbed end, the NSC car’s end is a solid, flat panel. Also, the NSC cars were built just before the introduction of CP Rail’s new “MultiMark” paint scheme, and were thus delivered in the older black paint. Interestingly, these cars were painted in simple block lettering, even though the Canadian Pacific script lettering was then the current lettering scheme in use at the time.

img0132

CP 336702 at Guelph Junction, sometime in the 1990s. Jurgen Kleylein photo.

The first step was to disassemble the car and remove most of the little detail bits. Then I cut away the original end with a razor saw and cleaned things up with a file. The side extensions that cap off the horizontal end ribs were also cut back and the bottom rib, which is below the level of the interior floor on the model, was carved away and things filed smooth. Then a plate of .040″ thick styrene was installed in the opening to form the core of the new end. The surface of this plate needs to be flush with the rest of the cleaned up end for the rest of the project to work.

IMG_8483IMG_8482

With the core of the new end in place, I cut away the protruding tail ends of the top chords of the sides flush with the end plate, and started framing in the new end with a 2×6 top chord and 2×4 framing around the sides and bottom. (Actually in the photo below I goofed and used a 4×6 on the top chord, which roughly matched the thickness of the top chord on the sides, but checking the prototype photo above, you can see it’s not actually that prominent on the end and is a lot more flush, so I had to cut this away and replace it with thinner material.)

IMG_8488

The basic assembly of the end was then finished off by cutting and filing a rectangle of .010″ styrene to fit snugly inside the end framing. Ladders and other details still need to be re-added, but here you can see the assembled end compared to the original ExactRail end on the car to the left.

IMG_8493

We now interrupt your regularly scheduled programming…

Posted on by
2

Ok, this one really has nothing to do with the Algoma Central, but I just love these oddball cars. This CP 40′ boxcar is a project that I’ve been working on that will ultimately see service down at my model railway club.

The prototype for this car is one of a very small group of 40′ boxcars that were rebuilt to increase the internal capacity for hauling appliances (i.e. kitchen stoves, etc.). I built this model from an Intermountain 40′ boxcar kit, performing a similar chop job, splicing the various bits with sheet styrene to increase the height. The Intermountain kit has separate ends, doors and roof pieces which really lends itself to this conversion job.

IMG_8470

I got this car painted red quite some time ago, and it’s been languishing on the shelf for a while behind other projects and life in general. This evening I finally moved it back into the paint shop to spray on the black part of the “multimark” logo. This stretched car also had a stretched multimark to fit the area beside the door, so this was masked and painted on, making this a three-colour paint job. (The white was done first (after a grey primer), then the red, and then finally this evening, the black.)

Now it’s finally ready for decals!

Basic Underframe for AC 300

Posted on by
Reply

Sat down again to this project for a while this evening.

I managed to file down the back of the skirting on the “A” end of the car and glue the side back into the end to repair the earlier damage. The floor piece is now able to manuever past the skirting and set into the body. (It’s just dry-fit for now.)

I admit I’m not a total expert to everything that’s going on under passenger cars, and there’s a lot of variation from car to car. Also I don’t have any really nice close-up detail photos of the bottoms of these two cars. Based on the reference photos I do have, I tried to replicate the general outline of what’s under there using the Train Station Products passenger car detail set, which includes a variety of tanks and boxes and other details.

IMG_8465

It’s not the most super-detailed underframe, but starting to at least represent the profile of the real thing. I plan on adding at least some piping to represent the air brakes and electrical connections underneath. It’s not going to be 100% accurate, but at least it should have the general impression of the thing.