Category Archives: Freight Cars

Atlas 2014 Catalog and Announcements – HO AC GP38-2

Posted on by
Reply

Earlier this week, Atlas Model Railroad Co. posted their 2014 All-Scales Catalog. Inside the HO Scale Announcements section is an interesting item for Algoma Central fans: Algoma Central is one of the roadnames in the next upcoming release of their TrainMan series GP38-2.

scan0052

AC 201 at Sault Ste. Marie in September 1982. Francis J. Wiener photo, Chris van der Heide collection.

Several years ago, Canadian Hobbycraft had sponsored a custom run of GP38-2s in various Canadian paint schemes including less common shortlines like RaiLink and Algoma Central. These were produced using the Life-Like Proto2000 GP38-2. Of course this limited run has long been out of production, and while one or two might pop up on the secondhand market occasionally, new ones just aren’t available anymore.

The new Atlas model is in the TrainMan series, which is Atlas’s more “entry level” line; the model will have the same proven drive train as Atlas’s higher end “Master Series” but the body may have less of the fine detail, and it most likely won’t have the road-specific details like snowplow, nose headlight, cab front bell, single rear headlight, Canadian-style vertical steps etc. However this will still be a good enough stand in for most, and a good starting point for detailing for many others.

They currently list road numbers 200 and 202, although this could potentially still change before production. The prototype locomotives were built in 1981 by General Motors Diesel Division in London, ON as series AC 200-205. Most or all of them are still operating today (just not in ACR colours) as WC 2001-2006.

ACR From Blair 007

WC 2001 (ex-AC 200) at Steelton Yard before repainting into WC colours. Blair Smith photo.

Part of the ad copy in the catalog indicates matching cabooses will be available, and indeed, further down is a section with new paint schemes on the TrainMan series “steel cupola caboose”, including Algoma Central. Of course this model is based on a small north-eastern US prototype that isn’t remotely similar to any ACR cabooses. The catalog outline artwork shows a caboose numbered AC 9607; this number would correspond to one of the three ex-CP vans acquired in 1992-93. Rapido Trains produced a model of this caboose several years ago. Highball Graphics also has some ACR caboose decals that can be used to custom paint something a bit better than the TrainMan caboose into ACR colours.

One other announcement in the catalog which will be of significant interest to most Canadian modelers is not too much of a surprise: a new version of their 50′ NSC boxcar matching the features of cars owned by Canadian Pacific and Ontario Northland. (Previously they have run Canadian National and British Columbia Railway versions.)

img0336

CP (ex-CPI) 85718 newsprint service boxcar. Jurgen Kleylein photo.

The first run of this version contains three paint schemes: Ontario Northland (7700-7799 series), Canadian Pacific (CPI 85635-85734 series) and Quebec Central/CP* (QC 75100-75299 series). All of the paint schemes represent original factory paint jobs, and future releases of other CP repainted cars are likely in subsequent runs.

* Note: The outline graphics in the catalog show the QC cars as an apparent ex-CP patch job; I checked with Atlas and this is not how the actual cars will be decorated. They will properly represent the as-built appearance of the QC cars, which were built new with QC reporting marks and CP colours. (Quebec Central was a CP subsidiary absorbed in the 1930s. CP re-used the marks in the late 1970s as a method to have empty paper service boxcars routed back to eastern Canada by other roads.)

Build dates for the prototype cars represented by the model are as follows:

Series Build Date Qty. Note
CPI 85635-85734 * # 9-10/77 100 re# CP /78-/83
ONT 7600-7629 11/77 30
ONT 7700-7799 * 9/80 100
QC 75000-75099 11-12/79 100
QC 75100-75299 * 7-8/80 200
QGRY 75000-75299 $ 11-12/79, 7-8/80 81 ex-QC /98

* – Series represented by Atlas
# – Previous series CPI 85500-85634 (Built 3-5/75, 135 cars) are similar but have 10′ wide doors (vs. 9′ doors on all of the other above) and non-cushioned underframes
$ – QGRY series is non-inclusive.

Some woodpulp/paper traffic from mills on the CPR line on the north shore of Lake Superior routed over the ACR from the interchange at Franz (that’s a subject I may attempt to cover in more detail sometime in a dedicated post), and there’s evidence that some paper from the Ontario Northland (from mills at Iroquois Falls, and likely from Kapuskasing and Smooth Rock Falls following the takeover of the ex-CN Kapuskasing subdivision) so any of these cars would not be out of place on a period ACR layout. I’ll be getting a couple of these cars for sure to mix into my CP woodpulp/paper fleet.

AC 2902-2915 series ex-ONT boxcars from TrueLine Trains’ 40′ NSC boxcar – Part 1

Posted on by
Reply

In the late 1970s to early 1980s the Algoma Central acquired some secondhand equipment from northern Ontario’s other regional railroad, the Ontario Northland Railway. This consisted of about 30 open hoppers acquired in 1978 for general service (basically meaning sinter from Wawa) and a number of old 40′ boxcars. Quite a number of former Ontario Northland boxcars ended up with 10000 series work service numbers as tool and storage cars, and a small handful received standard fleet numbered in the 2902-2914 series. These cars were used for the railways own local on-line freight service, hauling company supplies and materials, express and less than carload traffic to various remote places along the line, for which the railroad was the only way to bring in any sort of supplies or building materials. The railway used to run a weekly wayfreight for this service. I consider it highly unlikely that these cars ever left AC rails.

These boxcars were originally built in 1947-48 for the Ontario Northland by National Steel Car in Hamilton, ON. A few years ago, True Line Trains made modeling these cars easier by producing a ready-to-run model of this car, which was exclusively rostered (as original purchasers) by Canadian National and Ontario Northland.

These cars did receive a few modifications though, so a little bit of work to the model is required.

SAMSUNG DIGIMAX 360

Here’s AC 2915 at the Steelton shops in 2004. The car’s running boards have been removed (a common modification as roof running boards on boxcars were banned from interchange service on all railways in the 1970s) and interestingly, the brake wheel on the end of the car has also been relocated to a lower mounting.

IMG_9211_9212

The first step obviously is to remove the running board (roof walk) from the car. It’s best to shear the mounting pins as you do this, or once removed, cut off the mounting pins and glue them back into the body mounting holes to plug them up. On the left side of the picture above, you can see how the mounting pins are located in the middle of several of the running board supports molded into the roof. While good for hiding the mounting pins when the running boards are installed, it’s a little visible when the running boards are removed. So I used a needle file to file the rounded housing around the mounting pin off into a flat running board support like all the others on the car.

IMG_9219

The next step is to similarly (and *carefully*) remove the ladders and end hardware details from the car, since the ladders will need to be cut down in height, and the brake wheel mounting reinstalled at the lower height. I cut the ladders off after the 5th rung from the bottom, following reference photographs.

IMG_9218

While I had everything removed, I didn’t like how far away from the side of the car the tack boards were mounted, so I trimmed the back off the tack board so that when I glue it back on using CA glue, the tack board is much more snug to the end of the car.

IMG_9220

While most of the cars in this series were in the Ontario Northland’s early brown paint scheme (like the 2915 at the top of this post), this particular car will be given the road number AC 2906, which was in the Ontario Northland’s jade green colours. I have several more of the True Line Trains cars in both jade and brown, so more of the brown cars will join this one.

The patching out of the former Ontario Northland name and logo was clearly done with a paint roller on the prototype cars, so I took out some mineral brown paint and hand painted the patchwork with a small brush.

That’s as far as I’ve gotten so far; the next step will be to remount the ladders and brake hardware, renumber the car with stencil decals and weather it. All in all, a pretty straightforward job however, made easy by TrueLine’s ready-to-run Ontario Northland models.

A couple of CP boxcars lettered

Posted on by
Reply

Almost finished off the lettering on another pair of CP 40′ standard boxcars, plus the ex-International of Maine roofless woodchip boxcar.

The lettering on all three is again from CDS dry transfer sets, with ACI labels, consolidated stencils, U-1 wheel inspection dots and some detail lettering from various Microscale sets.

The three cars just need a few finishing touches like installing trucks and couplers, then to be clear-coated and heavily weathered for service in the 1980s.

CP 257210:

IMG_9215

CP 259546:

IMG_9216

CP 31236:

IMG_9214

More love from Walthers for Algoma Central – 65′ Gondolas

Posted on by
Reply

Well this is interesting.

I was skimming over the product announcements in the latest Model Railroad Hobbyist online magazine and prominently displayed under Walthers was an announcement for several new paint schemes on their 65′ Thrall mill gondola – including Algoma Central.

A little bit of searching managed to turn up the product listing on Walthers’ site.

Of course these aren’t remotely accurate – the real cars from Algoma Central series AC 1001-1400 are 61′ (not 65′) inside length cars with riveted side construction (not welded like the model) and distinctive bulkhead ends.

ACR from Blair 039

AC 1014 at Steelton shops. Blair Smith photo.

On the other hand, the lettering style and font matches that used on the 61′ cars and looks well rendered, and if you’re careful and can touch up the paint cleanly, it could be possible to take a decorated car, shorten the end panels and scratchbuild the end bulkheads to come up with a pretty reasonable representation of one of these cars, which could be a huge advantage to modeling these cars as a decal set matching the font used on these cars doesn’t actually exist (the CDS dry transfer set is for the 52′ gons, matching the lettering font on the AC 601-875 which is a bit “blockier” in the curved letters like O and C) and adding a scratchbuilt bulkhead end to an existing model is easier than scratchbuilding the entire car, particularly with all of the side rivets.

Of course, since you’re chopping up a modern welded car to represent a prototype that was actually of riveted construction, this is still only a general representation, but with 400 of these cars rostered, they were actually more numerous and wide ranging than the 52′ gondolas and any serious ACR modeler really needs a fleet of these cars. Their large size and bulkhead ends made them particularly useful for everything from pulpwood logs to steel products, and loaded with steel from Algoma Steel these cars ranged all over North America, which means modelers of other Canadian railways can definitely also justify running one of these.

I might just pick up at least one of these to try the conversion and see how I like it.

Rapido 52′ Gondolas Arrived

Posted on by
Reply

This evening I stopped at the post office to pick up several packages – packages containing the new Rapido Trains 52′ Canadian gondolas. (I won’t tell you how many exactly I picked up, because this was partly a pooled group order of cars for the WRMRC layout, so better than half of the cars will end up belonging to others, but let’s just say I acquired “more than one” 6-pack of AC cars (plus a few CPs) for my own purposes.)

These models are based on a common design of 52’6″ gondola with riveted construction and drop ends that were built by Eastern Car Company during the 1940s-50s for most of the major Canadian railways. Similar cars were built by Canadian Car & Foundry and National Steel Car up into the early 1960s, with generally similar features, but some detail differences.

IMG_7351

The prototype Algoma Central cars were built in 1959-62 in two batches by National Steel Car. (AC 601-800 and 801-875. Another almost identical batch was built in 1962 as AC 900-924 with covers for coil steel service.) They actually differ from the model in two ways. One, the AC cars have a different style of structural ribs on the sides. While the model features the distinctive Z shaped ribs fashioned from simple angle stock, the later AC cars had a stamped rib with a more of a hat profile (if you cross-sectioned the rib). The AC cars were also a higher capacity car with a 4′ interior height instead of the 3’5″ height of the model. However, the number and spacing of the side ribs is still consistent on all of these Canadian cars, so that still makes these cars a better stand in than any model of an American prototype. (The older Proto2000 gondola, based on a design built by Greenville Steel Car and Bethlehem Steel Corp., was previously the best stand in, but has a different number of side ribs and panels, which alters the layout of the Algoma Central billboard lettering on the side of the car.)

The models are well packaged, but even so exercise care when removing the cars from the packaging and check for any minor damage in shipping. There’s been some reports of the delicate ribs damaged in shipping (I haven’t seen much of this yet, but I’ve only removed a couple of cars from their packaging so far) and I had a few ends knocked free and rattling around inside the box (the drop ends are just press fit in place, so this is no big deal).

Here’s a few photos of a sample AC and CP (Action Red scheme) car to see some of the detail on these new models:

IMG_8806 IMG_8816

The relief of the Z shaped ribs is a distinctive feature of this model. The individual ribs are actually separate pieces to achive this effect. So one will have to take some care when picking up these cars not to crush any delicate details.

IMG_8818

These CP red cars feature trucks with converted roller bearing journals, a nice touch.

IMG_8819

I weighed one car at 4.1oz, just slightly under the NMRA “recommended” weight for a 7″ car of 4.5oz (1oz + .5oz/inch), but then almost every factory car is slightly under this recommendation, and consistency is one of the most important things. The Rapido car actually weighed out exactly identical to one of the Proto2000 gondolas I had nearby.

And lastly, a couple of final shots of the two cars on my in progress switching layout. The cars both appeared to track and roll quite well, although admittedly I don’t have much track to roll them around on. The real test will be when we try dragging a set of these around in a train at the club layout.

IMG_8826 IMG_8828